EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Residual Stress Engineering for Wire Drawing of Austenitic Stainless Steel X5CrNi18-10 by Variation in Die Geometries—Effect of Drawing Speed and Process Temperature

René Selbmann iD, Jens Gibmeier iD, Nicola Simon iD, Verena Kräusel iD, Markus Bergmann

Materials · 02.03.2024 · 17 (5) · 1174

DOI: 10.3390/ma17051174 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 02.03.2024. Verfasst von René Selbmann und 4 weiteren Autor:innen. Beteiligte Einrichtung: Fraunhofer Institute for Machine Tools and Forming Technology (IWU), D-09126 Chemnitz, Germany. Die Arbeit wurde bisher 13-mal zitiert (Crossref) und nennt 30 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Deutsche Forschungsgemeinschaft.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

As a result of conventional wire-forming processes, the residual stress distribution in wires is frequently unfavorable for subsequent forming processes such as bending operations. High tensile residual stresses typically occur in the near-surface region of the wires and can limit further application and processability of the semi-finished products. This paper presents an approach for tailoring the residual stress distribution by modifying the forming process, especially with regard to the die geometry and the influence of the drawing velocity as well as the wire temperature. The aim is to mitigate the near-surface tensile residual stresses induced by the drawing process. Preliminary studies have shown that modifications in the forming zone of the dies have a significant impact on the plastic strain and deformation direction, and the approach can be applied to effectively reduce the process-induced near-surface residual stress distributions without affecting the diameter of the product geometry. In this first approach, the process variant using three different drawing die geometries was established for the metastable austenitic stainless steel X5CrNi18-10 (1.4301) using slow (20 mm/s) and fast (2000 mm/s) drawing velocities. The residual stress depth distributions were determined by means of incremental hole drilling. Complementary X-ray stress analysis was carried out to analyze the phase-specific residual stresses since strain-induced martensitic transformations occurred close to the surface as a consequence of the shear deformation and the frictional loading. This paper describes the setup of the drawing tools as well as the results of the experimental tests.

Schlagwörter

Stichwörter der Autor:innen

FE simulationdrawing speedresidual stress analysisresidual stress modificationwire drawing

Autor:innen und Institutionen

  • Fraunhofer Institute for Machine Tools and Forming Technology (IWU), D-09126 Chemnitz, Germany.
  • Institute for Applied Materials (IAM-WK)-Materials Science and Engineering, D-76131 Karlsruhe, Germany.

ORCID-Profile: René Selbmann, Jens Gibmeier, Nicola Simon, Verena Kräusel

Förderung

  • Deutsche Forschungsgemeinschaft

Zitieren

APA

Selbmann, R., Gibmeier, J., Simon, N., Kräusel, V., & Bergmann, M. (2024). Residual Stress Engineering for Wire Drawing of Austenitic Stainless Steel X5CrNi18-10 by Variation in Die Geometries—Effect of Drawing Speed and Process Temperature. Materials, 17(5), 1174. https://doi.org/10.3390/ma17051174

Vancouver

Selbmann R, Gibmeier J, Simon N, Kräusel V, Bergmann M. Residual Stress Engineering for Wire Drawing of Austenitic Stainless Steel X5CrNi18-10 by Variation in Die Geometries—Effect of Drawing Speed and Process Temperature. Materials. 2024;17(5):1174. doi:10.3390/ma17051174

BibTeX
@article{Selbmann2024,
  author = {Selbmann, René and Gibmeier, Jens and Simon, Nicola and Kräusel, Verena and Bergmann, Markus},
  title = {Residual Stress Engineering for Wire Drawing of Austenitic Stainless Steel X5CrNi18-10 by Variation in Die Geometries—Effect of Drawing Speed and Process Temperature},
  journal = {Materials},
  year = {2024},
  volume = {17},
  number = {5},
  pages = {1174},
  doi = {10.3390/ma17051174}
}
Kostenlos starten →