EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Effect of tooth brushing simulation on the surface properties of various resin‐matrix computer‐aided design/computer‐aided manufacturing ceramics

Evangelos Ximinis, Dimitrios Dionysopoulos iD, Constantinos Papadopoulos, Alexandros Tournavitis, Avraam Konstantinidis, Olga Naka iD

Journal of Esthetic and Restorative Dentistry · 2023

DOI: 10.1111/jerd.13043 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Esthetic and Restorative Dentistry, 2023. Verfasst von Evangelos Ximinis und 5 weiteren Autor:innen. Beteiligte Einrichtung: Department of Prosthodontics, Faculty of Dentistry, School of Health Sciences, Aristotle University of Thessaloniki, Thessaloniki, Greece. Hauptthemen laut MEDLINE: Dental Porcelain, Toothbrushing. Die Arbeit wurde bisher 9-mal zitiert (Crossref) und nennt 41 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Purpose

The purpose was to investigate the alterations in surface properties of different resin‐matrix CAD/CAM ceramics following tooth brushing simulation (TBS) and compare them with a direct resin composite and a glass ceramic CAD/CAM material. Materials and methods Four resin‐based CAD/CAM restoratives (Brilliant Crios—BR, Lava™ Ultimate—LV, Grandio Blocs—GR and Shofu Block HC—SH), a leucite‐reinforced glass ceramic (IPS Empress® CAD—EC) and a resin composite (Filtek™ Z250—FZ) for direct restorations were tested. In particular, surface loss, hardness, roughness and morphology were investigated utilizing confocal microscopy, scanning electron microscopy and nanoindentation tester. TBS was conducted for 4 × 15 min on the surface of the samples and then the changes in their surface properties were evaluated.

Results

After TBS, all the experimental groups exhibited surface loss to different extent. FZ and BR presented the highest surface loss, while EC and GR the lowest ( p < 0.05). Regarding surface roughness, all the tested materials exhibited increase after TBS ( p < 0.05), except LV ( p = 0.099). EC presented the lowest Sa values, while FZ and BR the highest ( p < 0.05). Changes in surface morphology were in compliance with the results of surface roughness and also surface hardness was correlated with surface loss.

Conclusions

The tested resin‐matrix CAD/CAM ceramic restorative materials showed a competent behavior against abrasive forces applied during TBS. Surface loss and roughness changes were material dependent and superior compared to a resin composite for direct restorations, while in comparison with a leucite‐reinforced glass ceramic exhibited inferior properties. Clinical significance Tooth brushing affected differently the surface of the tested restorative materials. However, the abrasive wear that was induced was negligible. Clinical studies are necessary to ascertain if there is clinical significance of these surface alterations that may demand repair of such restorations.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Dental PorcelainToothbrushingCeramicsComposite ResinsDental MaterialsComputer-Aided DesignSurface PropertiesMaterials TestingAluminum Silicates

Stichwörter der Autor:innen

leucite-reinforced glass ceramicsresin-matrix CAD/CAM ceramicssurface losssurface roughnesstooth brushing simulation

Substanzen

Dental PorcelainComposite ResinsDental MaterialsleuciteAluminum Silicates

Autor:innen und Institutionen

  • Department of Prosthodontics, Faculty of Dentistry, School of Health Sciences, Aristotle University of Thessaloniki, Thessaloniki, Greece.
  • Department of Operative Dentistry, School of Health Sciences, Faculty of Dentistry, Aristotle University of Thessaloniki, Thessaloniki, Greece.
  • Department of Civil Engineering, Division of Structural Engineering, Faculty of Engineering, Aristotle University of Thessaloniki, Thessaloniki, Greece.

ORCID-Profile: Dimitrios Dionysopoulos, Olga Naka

Zitieren

APA

Ximinis, E., Dionysopoulos, D., Papadopoulos, C., Tournavitis, A., Konstantinidis, A., & Naka, O. (2023). Effect of tooth brushing simulation on the surface properties of various resin‐matrix computer‐aided design/computer‐aided manufacturing ceramics. Journal of Esthetic and Restorative Dentistry. https://doi.org/10.1111/jerd.13043

Vancouver

Ximinis E, Dionysopoulos D, Papadopoulos C, Tournavitis A, Konstantinidis A, Naka O. Effect of tooth brushing simulation on the surface properties of various resin‐matrix computer‐aided design/computer‐aided manufacturing ceramics. Journal of Esthetic and Restorative Dentistry. 2023. doi:10.1111/jerd.13043

BibTeX
@article{Ximinis2023,
  author = {Ximinis, Evangelos and Dionysopoulos, Dimitrios and Papadopoulos, Constantinos and Tournavitis, Alexandros and Konstantinidis, Avraam and Naka, Olga},
  title = {Effect of tooth brushing simulation on the surface properties of various resin‐matrix computer‐aided design/computer‐aided manufacturing ceramics},
  journal = {Journal of Esthetic and Restorative Dentistry},
  year = {2023},
  doi = {10.1111/jerd.13043}
}
Kostenlos starten →